Exclusive series of original fully-glazed entrance doors, in which a glass panel is inserted into a frame. It is a timeless, ecological product with perfect thermal insulation properties. Glass not only looks good but also has great properties. We always use safety glass only. We produce double-glazed panels (U = 1,1) or triple-glazed panels (U = 0,6). The glass can be sandblasted, digitally printed or colour sprayed, depending on the design. Fully-glazed doors have an attractive look and feel with their simplicity and elegance thanks to the use of glass.
WHAT IS SANDBLASTING?
It is the operation of forcibly propelling a stream of abrasive material against a glass under high pressure. As a result, the glass will become opaque and will get its typical “milk” tones.
WHAT IS A DIGITAL PRINT / COLOURED SPRAY?
Thanks to digital technology, we can print difficult patterns or even high resolution photos directly on the glass, which opens endless choices to your fantasy and creativity. For simple patterns we use coloured spray.
WHY IS THIS DOOR PANEL FILLED WITH ARGON?
Argon is a non-toxic gas, which increases thermal and sound insulation of the whole glass panel. It is used to fill the air gap in between the glass. Less noise, more heat and therefore lower bills for heating.
WHAT IS THE DIFFERENCE BETWEEN DOUBLE-GLAZING AND TRIPLE-GLAZING?
Double-glazing is nowadays mostly used in older apartment blocks, non-residential buildings or warehouses. The advantage of double-glazing is the low cost and weight and the disadvantage is significantly higher loss of heat. Triple-glazing is used mainly in new buildings, low energy and passive houses. The triple-glazed panel has much better thermal insulation, lower condensation, better sound insulation and it is safer in general. With triple-glazing you will get to keep up to 45% more heat in your house and lower your bills for heating at the same time.
AND WHAT ABOUT THE ENVIRONMENT?
By purchasing fully-glazed doors you also care for the environment because 96% of materials used in production are fully recyclable.
Doors with Vision Glass SAND door panel
Structure of the panel – sandblasting.
DOUBLE-GLAZING
Exterior glass is 33.1 CONNEX
Interior glass is 33.1 PLANITHERM XN
U = 1,1 W/(m²K) filled with argon
Thickness of the panel is 28 mm
TRIPLE-GLAZING
Exterior glass is 33.1 PLANITHERM XN
Middle glass is FLOAT
Interior glass is 33.1 PLANITHERM XN
U = 0,6 W/(m²K) filled with argon
Thickness of the panel is 48 mm
Doors with Vision Glass DIGITAL door panel
Structure of the panel – digital print and coloured spray.
DOUBLE-GLAZING
Exterior glass is 33.1 PLANITHERM XN
Interior glass is ESG MATELUX
U = 1,1 W/(m²K) filled with argon
Thickness of the panel is 28 mm
TRIPLE-GLAZING
Exterior glass is 33.1 PLANITHERM XN
Middle glass is ESG MATELUX
Interior glass is 33.1 PLANITHERM XN
U = 0,6 W/(m²K) filled with argon
Thickness of the panel is 50 mm
Doors with Vision Glass INOX door panel
Structure of the panel – inox.
TRIPLE-GLAZING
Exterior glass is 33.1 PLANITHERM XN
Middle glass is FLOAT
Interior glass is 33.1 PLANITHERM XN
U = 0,6 W/(m²K) filled with argon
Thickness of the panel is 48 mm
The aluminum door in RAL colours we make either as an inserted panel, one-sided attachment or double-sided attachment panel. With aluminum doors, it is possible to order Tiffany stained glass or resin stained glass, which is a perfect and significantly cheaper imitation. We offer two basic structures: Standard which is the simplest and consists only of XPS polystyrene and Standard+, where in addition to XPS polystyrene is also an aluminum sheet to increase the stiffness of the door. In addition to these two basic structures, we also offer premium structures with excellent thermal insulation values that are ideal for low energy and passive homes (Term Max and Term Plus), where the emphasis is on the lowest value of U. The TRD structure is ideally suited to extreme conditions where the doors are in dark colours and the sun shines all day – synthetic rubber EPDM absorbs thermal expansions up to 2.5mm.
The table above also contains EVO structure used for Evolution and Evolution INOX glass-aluminum entrance door. On the picture below are the basic structures Standard and Standard+. For example, Standard 24mm structure is the cheapest but its heat transfer coefficient reaches a much lower value of U = 1.39 W / (m²K). It is also the simplest structure made of extruded XPS polystyrene only. This structure provides good insulating properties and adequate stiffness for the price. In addition to the extruded XPS polystyrene, Standard+ structure also has an aluminum sheet that increases the overall stiffness of the door and therefore makes good price / quality choice.
Types of glazing
HPL is a resin-based material produced at high pressures and temperatures. It is harder and has lower thermal expansion than PVC. We have 35 types of glazing and 26 types of decor. For HPL with glazing, it is possible to order Tiffany stained glass or resin staining, which is a perfect and cheaper imitation.
Standard is the simplest structure made of extruded XPS polystyrene. This structure provides good insulating properties and adequate stiffness. In addition to the extruded XPS polystyrene, Standard+ structure also has an aluminum sheet that increases the overall stiffness of the door and is therefore a good price / quality solution. Stabil structure consists of extruded polystyrene XPS and waterproof plywood. It was created in response to the problem of thermal expansion. Stabil provides excellent rigidity and durability even under more challenging conditions. Extrem structure provides the highest stiffness and resistance in the HPL category. It consists of XPS extruded polystyrene, waterproof plywood and aluminum sheet. This structure will provide extraordinary security to your door together with a quality frame and lock.
Types of decors and colours for HPL
Types of glazing
Doors with PVC panels form the basis of our catalog. We have 35 types of glazing and 10 types of decor. For PVC doors with glazing it is possible to order Tiffany stained glass or resin staining, which is a perfect and cheaper imitation. In addition, it is also possible to desing the area around glazing in a classic way (Design Classic) or hide the fame in a structure (Design Plus).
Standard is the simplest structure made of extruded XPS polystyrene. The heat transfer coefficient in the base structure Standard with a thickness of 44 mm is U = 0.76 W / (m²K). This structure provides good insulating properties and adequate stiffness. In addition to the extruded XPS polystyrene, Standard+ structure also has an aluminum sheet that increases the overall stiffness of the door and is therefore a good price / quality solution. Universal was originally created for PVC door panels with overlays but is also suitable for other types of PVC doors. It has good insulating properties and high stiffness. Stabil structure consists of extruded polystyrene XPS and waterproof plywood. It was created in response to the problem of thermal expansion. Stabil provides excellent rigidity and durability even under more challenging conditions. Extrem structure provides the highest stiffness and resistance in the PVC category. It consists of XPS extruded polystyrene, waterproof plywood and aluminum sheet. This structure will provide extraordinary security to your door together with a quality frame and lock.
Colours and decors for PVC
Types of glazing